Merge branch 'dev' into dev

esphome/components/ethernet/ethernet_component.cpp

@@ -631,7 +631,7 @@ void EthernetComponent::write_phy_register_(esp_eth_mac_t *mac, PHYRegister regi
   ESPHL_ERROR_CHECK(err, "Writing PHY Register failed");
 
   if (this->type_ == ETHERNET_TYPE_RTL8201 && register_data.page) {
-    ESP_LOGD(TAG, "Select PHY Register Page 0x%02" PRIX32, 0x0);
+    ESP_LOGD(TAG, "Select PHY Register Page 0x00");
     err = mac->write_phy_reg(mac, this->phy_addr_, eth_phy_psr_reg_addr, 0x0);
     ESPHL_ERROR_CHECK(err, "Select PHY Register Page 0 failed");
   }

esphome/components/gpio/one_wire/gpio_one_wire.cpp

@@ -60,7 +60,7 @@ void HOT IRAM_ATTR GPIOOneWireBus::write_bit_(bool bit) {
   // recovery time: t_rec: min=1µs
   // ds18b20 appears to read the bus after roughly 14µs
   uint32_t delay0 = bit ? 6 : 60;
-  uint32_t delay1 = bit ? 54 : 5;
+  uint32_t delay1 = bit ? 59 : 5;
 
   // delay A/C
   delayMicroseconds(delay0);

esphome/components/ili9xxx/ili9xxx_display.cpp

@@ -34,8 +34,8 @@ void ILI9XXXDisplay::setup() {
   ESP_LOGD(TAG, "Setting up ILI9xxx");
 
   this->setup_pins_();
-  this->init_lcd_(this->init_sequence_);
+  this->init_lcd(this->init_sequence_);
-  this->init_lcd_(this->extra_init_sequence_.data());
+  this->init_lcd(this->extra_init_sequence_.data());
   switch (this->pixel_mode_) {
     case PIXEL_MODE_16:
       if (this->is_18bitdisplay_) {
@@ -405,7 +405,7 @@ void ILI9XXXDisplay::reset_() {
   }
 }
 
-void ILI9XXXDisplay::init_lcd_(const uint8_t *addr) {
+void ILI9XXXDisplay::init_lcd(const uint8_t *addr) {
   if (addr == nullptr)
     return;
   uint8_t cmd, x, num_args;
@@ -427,6 +427,20 @@ void ILI9XXXDisplay::init_lcd_(const uint8_t *addr) {
   }
 }
 
+void ILI9XXXGC9A01A::init_lcd(const uint8_t *addr) {
+  if (addr == nullptr)
+    return;
+  uint8_t cmd, x, num_args;
+  while ((cmd = *addr++) != 0) {
+    x = *addr++;
+    num_args = x & 0x7F;
+    this->send_command(cmd, addr, num_args);
+    addr += num_args;
+    if (x & 0x80)
+      delay(150);  // NOLINT
+  }
+}
+
 // Tell the display controller where we want to draw pixels.
 void ILI9XXXDisplay::set_addr_window_(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2) {
   x1 += this->offset_x_;

esphome/components/ili9xxx/ili9xxx_display.h

@@ -109,7 +109,7 @@ class ILI9XXXDisplay : public display::DisplayBuffer,
 
   virtual void set_madctl();
   void display_();
-  void init_lcd_(const uint8_t *addr);
+  virtual void init_lcd(const uint8_t *addr);
   void set_addr_window_(uint16_t x, uint16_t y, uint16_t x2, uint16_t y2);
   void reset_();
 
@@ -269,6 +269,7 @@ class ILI9XXXS3BoxLite : public ILI9XXXDisplay {
 class ILI9XXXGC9A01A : public ILI9XXXDisplay {
  public:
   ILI9XXXGC9A01A() : ILI9XXXDisplay(INITCMD_GC9A01A, 240, 240, true) {}
+  void init_lcd(const uint8_t *addr) override;
 };
 
 //-----------   ILI9XXX_24_TFT display --------------

esphome/components/mqtt/mqtt_datetime.cpp

@@ -6,12 +6,12 @@
 #include "mqtt_const.h"
 
 #ifdef USE_MQTT
-#ifdef USE_DATETIME_TIME
+#ifdef USE_DATETIME_DATETIME
 
 namespace esphome {
 namespace mqtt {
 
-static const char *const TAG = "mqtt.datetime.time";
+static const char *const TAG = "mqtt.datetime.datetime";
 
 using namespace esphome::datetime;
 
@@ -80,5 +80,5 @@ bool MQTTDateTimeComponent::publish_state(uint16_t year, uint8_t month, uint8_t
 }  // namespace mqtt
 }  // namespace esphome
 
-#endif  // USE_DATETIME_TIME
+#endif  // USE_DATETIME_DATETIME
 #endif  // USE_MQTT

esphome/components/mqtt/mqtt_datetime.h

@@ -3,7 +3,7 @@
 #include "esphome/core/defines.h"
 
 #ifdef USE_MQTT
-#ifdef USE_DATETIME_TIME
+#ifdef USE_DATETIME_DATETIME
 
 #include "esphome/components/datetime/datetime_entity.h"
 #include "mqtt_component.h"
@@ -17,7 +17,7 @@ class MQTTDateTimeComponent : public mqtt::MQTTComponent {
    *
    * @param time The time entity.
    */
-  explicit MQTTDateTimeComponent(datetime::DateTimeEntity *time);
+  explicit MQTTDateTimeComponent(datetime::DateTimeEntity *datetime);
 
   // ========== INTERNAL METHODS ==========
   // (In most use cases you won't need these)
@@ -41,5 +41,5 @@ class MQTTDateTimeComponent : public mqtt::MQTTComponent {
 }  // namespace mqtt
 }  // namespace esphome
 
-#endif  // USE_DATETIME_DATE
+#endif  // USE_DATETIME_DATETIME
 #endif  // USE_MQTT

esphome/components/veml7700/veml7700.cpp

@@ -243,7 +243,7 @@ ErrorCode VEML7700Component::configure_() {
   }
 
   PSMRegister psm{0};
-  psm.PSM = PSM::PSM_MODE_1;
+  psm.PSM = PSMMode::PSM_MODE_1;
   psm.PSM_EN = false;
   ESP_LOGV(TAG, "Setting PSM to 0x%04X", psm.raw);
   err = this->write_register((uint8_t) CommandRegisters::PWR_SAVING, psm.raw_bytes, VEML_REG_SIZE);

esphome/components/veml7700/veml7700.h

@@ -24,7 +24,7 @@ enum class CommandRegisters : uint8_t {
   ALS_INT = 0x06      // R: ALS INT trigger event
 };
 
-enum Gain : uint8_t {
+enum Gain : uint16_t {
   X_1 = 0,
   X_2 = 1,
   X_1_8 = 2,
@@ -32,7 +32,7 @@ enum Gain : uint8_t {
 };
 const uint8_t GAINS_COUNT = 4;
 
-enum IntegrationTime : uint8_t {
+enum IntegrationTime : uint16_t {
   INTEGRATION_TIME_25MS = 0b1100,
   INTEGRATION_TIME_50MS = 0b1000,
   INTEGRATION_TIME_100MS = 0b0000,
@@ -42,14 +42,14 @@ enum IntegrationTime : uint8_t {
 };
 const uint8_t INTEGRATION_TIMES_COUNT = 6;
 
-enum Persistence : uint8_t {
+enum Persistence : uint16_t {
   PERSISTENCE_1 = 0,
   PERSISTENCE_2 = 1,
   PERSISTENCE_4 = 2,
   PERSISTENCE_8 = 3,
 };
 
-enum PSM : uint8_t {
+enum PSMMode : uint16_t {
   PSM_MODE_1 = 0,
   PSM_MODE_2 = 1,
   PSM_MODE_3 = 2,
@@ -92,7 +92,7 @@ union PSMRegister {
   uint8_t raw_bytes[2];
   struct {
     bool PSM_EN : 1;
-    uint8_t PSM : 2;
+    PSMMode PSM : 2;
     uint16_t reserved : 13;
   } __attribute__((packed));
 };

esphome/components/voice_assistant/voice_assistant.cpp

@@ -799,7 +799,7 @@ void VoiceAssistant::on_audio(const api::VoiceAssistantAudio &msg) {
     this->speaker_buffer_index_ += msg.data.length();
     this->speaker_buffer_size_ += msg.data.length();
     this->speaker_bytes_received_ += msg.data.length();
-    ESP_LOGV(TAG, "Received audio: %" PRId32 " bytes from API", msg.data.length());
+    ESP_LOGV(TAG, "Received audio: %u bytes from API", msg.data.length());
   } else {
     ESP_LOGE(TAG, "Cannot receive audio, buffer is full");
   }

tests/components/a01nyub/common.yaml

@@ -0,0 +1,11 @@
+uart:
+  - id: uart_a01nyub
+    tx_pin: ${tx_pin}
+    rx_pin: ${rx_pin}
+    baud_rate: 9600
+
+sensor:
+  - platform: a01nyub
+    id: a01nyub_sensor
+    name: a01nyub Distance
+    uart_id: uart_a01nyub

tests/components/a01nyub/test.esp32-c3-idf.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO4
-    tx_pin:
+  rx_pin: GPIO5
-      number: 4
-    rx_pin:
-      number: 5
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/a01nyub/test.esp32-c3.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO4
-    tx_pin:
+  rx_pin: GPIO5
-      number: 4
-    rx_pin:
-      number: 5
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/a01nyub/test.esp32-idf.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO17
-    tx_pin:
+  rx_pin: GPIO16
-      number: 17
-    rx_pin:
-      number: 16
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/a01nyub/test.esp32.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO17
-    tx_pin:
+  rx_pin: GPIO16
-      number: 17
-    rx_pin:
-      number: 16
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/a01nyub/test.esp8266.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO4
-    tx_pin:
+  rx_pin: GPIO5
-      number: 4
-    rx_pin:
-      number: 5
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/a01nyub/test.rp2040.yaml

@@ -1,13 +1,5 @@
-uart:
+substitutions:
-  - id: uart_a01nyub
+  tx_pin: GPIO4
-    tx_pin:
+  rx_pin: GPIO5
-      number: 4
-    rx_pin:
-      number: 5
-    baud_rate: 9600
 
-sensor:
+<<: !include common.yaml
-  - platform: a01nyub
-    id: a01nyub_sensor
-    name: a01nyub Distance
-    uart_id: uart_a01nyub

tests/components/api/common.yaml

@@ -50,12 +50,12 @@ api:
       then:
         - logger.log:
             # yamllint disable rule:line-length
-            format: "Bool: %s (%u), Int: %d (%u), Float: %f (%u), String: %s (%u)"
+            format: "Bool: %s (%u), Int: %ld (%u), Float: %f (%u), String: %s (%u)"
             # yamllint enable rule:line-length
             args:
               - YESNO(bool_arr[0])
               - bool_arr.size()
-              - int_arr[0]
+              - (long) int_arr[0]
               - int_arr.size()
               - float_arr[0]
               - float_arr.size()

tests/components/esp32_hall/common.yaml

@@ -1,3 +0,0 @@
-sensor:
-  - platform: esp32_hall
-    name: ESP32 Hall Sensor

tests/components/esp32_hall/test.esp32-idf.yaml

@@ -1 +0,0 @@
-<<: !include common.yaml

tests/components/esp32_hall/test.esp32.yaml

@@ -1 +1,3 @@
-<<: !include common.yaml
+sensor:
+  - platform: esp32_hall
+    name: ESP32 Hall Sensor

tests/components/ethernet/common-dp83848.yaml

@@ -1,5 +1,5 @@
 ethernet:
-  type: LAN8720
+  type: DP83848
   mdc_pin: 23
   mdio_pin: 25
   clk_mode: GPIO0_IN

tests/components/ethernet/common-ip101.yaml

@@ -1,5 +1,5 @@
 ethernet:
-  type: LAN8720
+  type: IP101
   mdc_pin: 23
   mdio_pin: 25
   clk_mode: GPIO0_IN

tests/components/ethernet/common-jl1101.yaml

@@ -0,0 +1,12 @@
+ethernet:
+  type: JL1101
+  mdc_pin: 23
+  mdio_pin: 25
+  clk_mode: GPIO0_IN
+  phy_addr: 0
+  power_pin: 26
+  manual_ip:
+    static_ip: 192.168.178.56
+    gateway: 192.168.178.1
+    subnet: 255.255.255.0
+  domain: .local

tests/components/ethernet/common-ksz8081.yaml

@@ -0,0 +1,12 @@
+ethernet:
+  type: KSZ8081
+  mdc_pin: 23
+  mdio_pin: 25
+  clk_mode: GPIO0_IN
+  phy_addr: 0
+  power_pin: 26
+  manual_ip:
+    static_ip: 192.168.178.56
+    gateway: 192.168.178.1
+    subnet: 255.255.255.0
+  domain: .local

tests/components/ethernet/common-ksz8081rna.yaml

@@ -0,0 +1,12 @@
+ethernet:
+  type: KSZ8081RNA
+  mdc_pin: 23
+  mdio_pin: 25
+  clk_mode: GPIO0_IN
+  phy_addr: 0
+  power_pin: 26
+  manual_ip:
+    static_ip: 192.168.178.56
+    gateway: 192.168.178.1
+    subnet: 255.255.255.0
+  domain: .local

tests/components/ethernet/common-rtl8201.yaml

@@ -0,0 +1,12 @@
+ethernet:
+  type: RTL8201
+  mdc_pin: 23
+  mdio_pin: 25
+  clk_mode: GPIO0_IN
+  phy_addr: 0
+  power_pin: 26
+  manual_ip:
+    static_ip: 192.168.178.56
+    gateway: 192.168.178.1
+    subnet: 255.255.255.0
+  domain: .local

tests/components/ethernet/common-w5500.yaml

@@ -1,11 +1,11 @@
 ethernet:
   type: W5500
-  clk_pin: GPIO19
+  clk_pin: 19
-  mosi_pin: GPIO21
+  mosi_pin: 21
-  miso_pin: GPIO23
+  miso_pin: 23
-  cs_pin: GPIO18
+  cs_pin: 18
-  interrupt_pin: GPIO36
+  interrupt_pin: 36
-  reset_pin: GPIO22
+  reset_pin: 22
   clock_speed: 10Mhz
   manual_ip:
     static_ip: 192.168.178.56

tests/components/ethernet/test-dp83848.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-dp83848.yaml

tests/components/ethernet/test-dp83848.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-dp83848.yaml

tests/components/ethernet/test-ip101.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-ip101.yaml

tests/components/ethernet/test-ip101.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-ip101.yaml

tests/components/ethernet/test-jl1101.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-jl1101.yaml

tests/components/ethernet/test-jl1101.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-jl1101.yaml

tests/components/ethernet/test-ksz8081.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-ksz8081.yaml

tests/components/ethernet/test-ksz8081.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-ksz8081.yaml

tests/components/ethernet/test-ksz8081rna.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-ksz8081rna.yaml

tests/components/ethernet/test-ksz8081rna.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-ksz8081rna.yaml

tests/components/ethernet/test-lan8720.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-lan8720.yaml

tests/components/ethernet/test-lan8720.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-lan8720.yaml

tests/components/ethernet/test-rtl8201.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-rtl8201.yaml

tests/components/ethernet/test-rtl8201.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-rtl8201.yaml

tests/components/ethernet/test-w5500.esp32-idf.yaml

@@ -0,0 +1 @@
+<<: !include common-w5500.yaml

tests/components/ethernet/test-w5500.esp32.yaml

@@ -0,0 +1 @@
+<<: !include common-w5500.yaml

tests/components/ethernet/test.esp32-idf.yaml

@@ -1 +0,0 @@
-<<: !include common.yaml

tests/components/ethernet/test.esp32.yaml

@@ -1 +0,0 @@
-<<: !include common.yaml

tests/components/ethernet/w5500.esp32-idf.yaml

@@ -1,14 +0,0 @@
-ethernet:
-  type: W5500
-  clk_pin: GPIO19
-  mosi_pin: GPIO21
-  miso_pin: GPIO23
-  cs_pin: GPIO18
-  interrupt_pin: GPIO36
-  reset_pin: GPIO22
-  clock_speed: 10Mhz
-  manual_ip:
-    static_ip: 192.168.178.56
-    gateway: 192.168.178.1
-    subnet: 255.255.255.0
-  domain: .local

tests/components/http_request/common.yaml

@@ -15,10 +15,10 @@ esphome:
           on_response:
             then:
               - logger.log:
-                  format: "Response status: %d, Duration: %u ms"
+                  format: "Response status: %d, Duration: %lu ms"
                   args:
                     - response->status_code
-                    - response->duration_ms
+                    - (long) response->duration_ms
       - http_request.post:
           url: https://esphome.io
           headers:

tests/components/wireguard/common.yaml

@@ -0,0 +1,59 @@
+wifi:
+  ssid: "MySSID1"
+  password: "password1"
+
+time:
+  - platform: sntp
+
+wireguard:
+  address: 172.16.34.100
+  netmask: 255.255.255.0
+  # NEVER use the following keys for your VPN -- they are now public!
+  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
+  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
+  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
+  peer_endpoint: wg.server.example
+  peer_persistent_keepalive: 25s
+  peer_allowed_ips:
+    - 172.16.34.0/24
+    - 192.168.4.0/24
+
+binary_sensor:
+  - platform: wireguard
+    status:
+      name: 'WireGuard Status'
+    enabled:
+      name: 'WireGuard Enabled'
+
+sensor:
+  - platform: wireguard
+    latest_handshake:
+      name: 'WireGuard Latest Handshake'
+
+text_sensor:
+  - platform: wireguard
+    address:
+      name: 'WireGuard Address'
+
+button:
+  - platform: template
+    name: 'Toggle WireGuard'
+    entity_category: config
+    on_press:
+      - if:
+          condition: wireguard.enabled
+          then:
+            - wireguard.disable:
+          else:
+            - wireguard.enable:
+
+  - platform: template
+    name: 'Log WireGuard status'
+    entity_category: config
+    on_press:
+      - if:
+          condition: wireguard.peer_online
+          then:
+            - logger.log: 'wireguard remote peer is online'
+          else:
+            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.bk72xx.yaml

@@ -1,59 +1 @@
-wifi:
+<<: !include common.yaml
-  ssid: "MySSID1"
-  password: "password1"
-
-time:
-  - platform: sntp
-
-wireguard:
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.esp32-c3-idf.yaml

@@ -1,60 +1 @@
-wifi:
+<<: !include common.yaml
-  ssid: MySSID
-  password: password1
-
-time:
-  - platform: sntp
-
-wireguard:
-  id: vpn
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.esp32-c3.yaml

@@ -1,60 +1 @@
-wifi:
+<<: !include common.yaml
-  ssid: MySSID
-  password: password1
-
-time:
-  - platform: sntp
-
-wireguard:
-  id: vpn
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.esp32-idf.yaml

@@ -1,62 +1,4 @@
-wifi:
+<<: !include common.yaml
-  ssid: "MySSID1"
-  password: "password1"
 
 network:
   enable_ipv6: true
-
-time:
-  - platform: sntp
-
-wireguard:
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.esp32.yaml

@@ -1,62 +1,4 @@
-wifi:
+<<: !include common.yaml
-  ssid: "MySSID1"
-  password: "password1"
 
 network:
   enable_ipv6: true
-
-time:
-  - platform: sntp
-
-wireguard:
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'

tests/components/wireguard/test.esp8266.yaml

@@ -1,62 +1,4 @@
-wifi:
+<<: !include common.yaml
-  ssid: "MySSID1"
-  password: "password1"
 
 network:
   enable_ipv6: true
-
-time:
-  - platform: sntp
-
-wireguard:
-  address: 172.16.34.100
-  netmask: 255.255.255.0
-  # NEVER use the following keys for your vpn, they are now public!
-  private_key: wPBMxtNYH3mChicrbpsRpZIasIdPq3yZuthn23FbGG8=
-  peer_public_key: Hs2JfikvYU03/Kv3YoAs1hrUIPPTEkpsZKSPUljE9yc=
-  peer_preshared_key: 20fjM5GRnSolGPC5SRj9ljgIUyQfruv0B0bvLl3Yt60=
-  peer_endpoint: wg.server.example
-  peer_persistent_keepalive: 25s
-  peer_allowed_ips:
-    - 172.16.34.0/24
-    - 192.168.4.0/24
-
-binary_sensor:
-  - platform: wireguard
-    status:
-      name: 'WireGuard Status'
-    enabled:
-      name: 'WireGuard Enabled'
-
-sensor:
-  - platform: wireguard
-    latest_handshake:
-      name: 'WireGuard Latest Handshake'
-
-text_sensor:
-  - platform: wireguard
-    address:
-      name: 'WireGuard Address'
-
-button:
-  - platform: template
-    name: 'Toggle WireGuard'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.enabled
-          then:
-            - wireguard.disable:
-          else:
-            - wireguard.enable:
-
-  - platform: template
-    name: 'Log WireGuard status'
-    entity_category: config
-    on_press:
-      - if:
-          condition: wireguard.peer_online
-          then:
-            - logger.log: 'wireguard remote peer is online'
-          else:
-            - logger.log: 'wireguard remote peer is offline'