* Fix receive and transmit for RC5-protocol
Receive did not work as a sequence of two high or low puleses are detected as one long pulse. Transmit was extended to respect the field bit in order to enable codes up to 127.
* Fix code formatting
* Add fan support to bang bang controller
* Fix heat-only and cool-only modes
* Added support for all climate actions and modes
* Fix up some comments
* Fan_only mode behavior tweak
* Updated test
* Updated test, take 2
* Add accessor methods for easier use in lambadas
* Revert "Add accessor methods for easier use in lambadas"
This reverts commit f15713129cd5587242a08ad1e2ee37cbf075aa03.
Don't code late at night when sleepy.
* Fix single/dual setpoint support
* Linted
* Properly implement single-point, validation improvements
* Another quick fix...sigh
* Update tests
* Update tests, take 2
* Revert "Update tests, take 2"
This reverts commit 71bb7fccc53d95a7d221e80ea0a931fb3cfd9a0c.
Nope.
* Revert "Update tests"
This reverts commit 42044291efaaf09858f29ab27bbc3aa9e8b80ee9.
Nope 2.
* Updated/fixed tests
* Revert "Updated/fixed tests"
This reverts commit a1a5b1c7db9a240b9da668b6e48abe1dd7910777.
Taking a different approach.
* Revert "Another quick fix...sigh"
This reverts commit 6b1955724a2de3c2d1534ec206dd5794bbb5f568.
Taking a different approach.
* Revert "Properly implement single-point, validation improvements"
This reverts commit f5bfff099e1dc58edd3898da8655c147adde2301.
Taking a different approach.
* Single/dual set point fixes, full validation
* Fix test
* Fix restore-on-boot, clean up comments
* Decouple two-point/auto operation, more polish
* One last away mode tweak
* Added set point validation
* Clean up over-publishing, always call action after boot
* Add fan support to bang bang controller
* Fix heat-only and cool-only modes
* Added support for all climate actions and modes
* Fix up some comments
* Fan_only mode behavior tweak
* Updated test
* Updated test, take 2
* Add accessor methods for easier use in lambadas
* Revert "Add accessor methods for easier use in lambadas"
This reverts commit f15713129cd5587242a08ad1e2ee37cbf075aa03.
Don't code late at night when sleepy.
* Fix single/dual setpoint support
* Linted
* Properly implement single-point, validation improvements
* Another quick fix...sigh
* Update tests
* Update tests, take 2
* Revert "Update tests, take 2"
This reverts commit 71bb7fccc53d95a7d221e80ea0a931fb3cfd9a0c.
Nope.
* Revert "Update tests"
This reverts commit 42044291efaaf09858f29ab27bbc3aa9e8b80ee9.
Nope 2.
* Updated/fixed tests
* Revert "Updated/fixed tests"
This reverts commit a1a5b1c7db9a240b9da668b6e48abe1dd7910777.
Taking a different approach.
* Revert "Another quick fix...sigh"
This reverts commit 6b1955724a2de3c2d1534ec206dd5794bbb5f568.
Taking a different approach.
* Revert "Properly implement single-point, validation improvements"
This reverts commit f5bfff099e1dc58edd3898da8655c147adde2301.
Taking a different approach.
* Single/dual set point fixes, full validation
* Fix test
* Fix restore-on-boot, clean up comments
* Decouple two-point/auto operation, more polish
* One last away mode tweak
* Added set point validation
* Clean up over-publishing, always call action after boot
* Added refresh() function to allow easy on-device state refreshing
* ADE7953: Fix dereferencing of a null pointer
The ade7953 driver dereferences a null pointer, when not all of
its sensors are used. This gives an exception like:
Fatal exception:29 flag:2 (EXCEPTION) epc1:0x4020c241 epc2:0x00000000 epc3:0x00000000 excvaddr:0x00000018 depc:0x00000000
* Fix formatting
Co-authored-by: olg <x>
* Fix fan oscillation trait not being used
* Add fan direction support to SpeedFan
* Add fan direction to API
* Add fan direction support to BinaryFan
* Fix CI errors
* Fix python format
* Change some ordering to trigger CI
* Add test for the configuration
A component to support [WLED](https://github.com/Aircoookie/WLED/wiki/UDP-Realtime-Control).
This allows to control addressable LEDs over WiFi/UDP, by pushing data right into LEDs.
The most useful to use [Prismatik](https://github.com/psieg/Lightpack) to create
an immersive effect on PC.
It supports all WLED protocols:
- WARLS
- DRGB
- DRGBW
- DNRGB
- WLED Notifier
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
This adds a `e131` component that allows
to register `e131` addressable light effect.
This uses an internal implementation that
is thread-safe instead of using external libraries.
* making SPI CS optional
* CS pin should be declared as optional or required in CONFIG_SCHEMA
* changed SPI_DEVICE_SCHEMA to a function, like i2c
* added spi_device_schema() to pcd8544, lint fixes
* updated max31856 with new spi_device_schema()
* cleanup imports
Co-authored-by: Ilya Goldberg <iggie@mac.com>
* Turn off PN532 RF field when not expecting a tag
Avoids interference with Wifi connectivity of nearby devices.
* Rename turn_off_rf_ method
* documented off command bytes
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* Extend `uart:` with `rx_buffer_size:`
This allows to configure `rx_buffer_size:`
to efficiently receive big payloads over UART
* lint
* remove old default value
* add test
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* uart: Add support for specifying the number of bits and parity.
ESP8266SwSerial doesn't really check parity but just read the parity bit
and ignore it when receiving data.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: support begin and end methods.
A component may need to reset uart buffer/status by using begin() and
end() methods. This is useful for example when a component needs to be
sure it is not reading garbage from previously received data over uart.
For end() methods with software serial, disabling interrupt is
currently impossible because of a bug in esp8266 Core:
https://github.com/esp8266/Arduino/issues/6049
Signed-off-by: 0hax <0hax@protonmail.com>
* esphal: add support for detaching an interrupt.
That's needed when a component needs to enable/disable interrupt on a
gpio.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: rename CONF_NR_BITS to CONF_DATA_BITS_NUMBER.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: use static const uint32_t instead of #define.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: use an enum to handle parity.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: split between esp32 and esp8266.
Signed-off-by: 0hax <0hax@protonmail.com>
* uart: check_uart_settings for parity and number of data bits.
Signed-off-by: 0hax <0hax@protonmail.com>
* name param data_bits
* add new params to test
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* Added auto discovery and setup to Dallas Platform
* Added auto discovery and setup to Dallas Platform
* Added auto discovery and setup to Dallas Platform
* Added auto discovery and setup to Dallas Platform
* Added auto discovery and setup to Dallas Platform
* Added ble_scanner component
* ble_scanner: time.h changed to ctime
* ble_scanner: Test added.
* ble_scanner: fixed code formatting.
* Removed duplicate binary sensor tests from test2 and test3 to decrease memory requirements.
* Removed another duplicate test from test2.yaml and moved stepper test to yaml3.yaml to reduce memory requirements of test2.yaml.
* Reverted the last stepper test change
* Moved some sensor tests from test2.yaml to test3.yaml to save memory.
* Moved ruuvitag back to test2.yaml as it requires component esp32_ble_tracker.
* removed apds9960 as it is duplicated
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* dht: Fix sensor reading from DHT22 (#239)
Looking at the datasheet for DHT22, it claims to need a delay of 18ms, not
800us. Change to use the same delay as DHT11. Tested working with NodeMCUv3
and DHT22 sensor with board with built-in resistor.
* dht: Add model DHT22_TYPE2 with 2ms delay instead of 0.8ms
The model DHT22_TYPE2 is exactly the same as DHT22, but uses a different
delay.
* dht: Fix bogus negative temperature reading on DHT22_TYPE2
The workaround for negative numbers associated with DHT22s can be skipped
on these sensors.
* Restructuring of static files directory
* Update jQuery to v3.5.0
* Update jQuery UI to v1.12.1
* Update jQuery Validate to v1.19.1
* Improve login page layout and color scheme
* Updated header & footer colour scheme & added ESPHome logo
* Restructuring of fonts directory
* Restructuring of fonts directory
* Corrected icon reference error
* Update node layout and styling
* Update Ace to v1.4.10
* JS file reorganisation
* Rewrite of LogModal class including refactorization of js & html
* Updated delete node function
* Rewrite of editor modal
* Update Materialize Stepper to v3.1.0
* Updates to the wizard modal
* Added wizard validators back in and removed comments
* Merge old stylesheet into new
* Linting errors
* Fixed dashboard layout issue when no nodes present
* Introduced dynamic 3 column layout for large screens
* Removed unnecessary code
* Update data attribute names
* Added loading indicator to editor
* Open validator websocket on document ready
* Automatically restart validator websocket if it closes
* Minor styling updates
* Improvements to on boarding process
* Node display filename and then path on hover
* Removing console.logs
* Minor styling revisions
* Added toast on begin
* Fix lint
Co-authored-by: Sergio Mayoral Martinez <sergiomayoralmartinez@gmail.com>
* esp32_ble_tracker: introduce UUID comparison function
* ble_presence, ble_rssi: use new UUID comparison function
* esp32_ble_tracker: introduce automation on BLE advertising
* test2.yaml: remove deep_sleep due to firmware size restrictions
